How to Install a Ghost Immobiliser
Ghost immobilisers protect your vehicle from key cloning or hacking. It prevents the engine from starting until a PIN number is entered. It can be as long as 20 characters.
It is not detected by thieves, who are unlikely to think about this additional layer of security. Some systems also have an app that allows owners to disarm the immobiliser in case they forget their PIN, or to use a service/valet mode.
Connecting to the vehicle's CAN bus
The Ghost 2 Immobiliser, a cutting edge security system, can be integrated directly into the ECU of your vehicle. It provides a discreet barrier against thieves. It is extremely efficient and user-friendly. This makes it a valuable asset to your vehicle's arsenal of security. However, like any anti-theft device, it is not 100% reliable and requires regular maintenance to ensure its operation. Luckily, this guide will aid you in getting the most out of your Ghost 2 Immobiliser.
CAN (Controller Area Network), a robust serial networking, allows microcontrollers communicate with each other over small distances. Central control units is not required. It is designed to multiplex electrical wiring in vehicles, which saves on copper. It offers many advantages including low cost and easy use.
In most modern cars in modern vehicles, the CAN protocol is used to connect with a variety of systems, including the engine management system (EMS), transmission controller, steering module as well as air conditioning controls and more. It also transmits sensor data including speed sensors and inputs, to control different features of the vehicle. The CAN bus is used to monitor these different components, and can prevent a vehicle from starting if they are in an unsafe state.
It is important to understand how the CAN bus functions and how it's secured. It's possible to add new features to vehicles using CAN bus, but it is important to protect it against attacks from hackers and other dangers. The best method to achieve this is to install a firewall and monitoring your CAN bus through software.
Ghost2's control unit is hidden in the dashboard of the car or in the wiring harness, preventing thieves from physically tampering with it. It is impossible to reset a PIN or an emergency code without access to the car.
If you must surrender your vehicle for servicing, valet parking, or any other reason, you can activate the Transport Mode. This feature disables both the keyfob and ignition functions of the Ghost immobiliser. It will only be activated after the vehicle has travelled 31 mph for a time of 15 minutes.
Making PIN codes
The Ghost immobiliser shields your vehicle from theft. The innovative technology uses the PIN to disable the vehicle's engine and prevent it starting without the correct code, or a valid fob/mobile. The system's sleek design is unnoticeable and provides unparalleled protection against theft. Moreover the system is TASSA certified and can provide significant savings on car insurance premiums.
During installation, Ghost enters a "learning mode" to record the sequences of buttons that are pressed to create your unique pin codes. After the pin code is created and the installer has completed its work, it will guide you through the steps to activate the system. Once activated it will Ghost system will turn off the motor that starts your vehicle until a valid pin code is entered or the vehicle is switched to transport mode. ghost 11 immobiliser makes it difficult for thieves or cloners to hack or clone your vehicle's starter system.
Installing an Ghost immobiliser is straightforward however it is essential to follow the specific instructions in the user's manual to ensure that it operates properly. Multimeters and basic hand tools can be used to verify electrical values. Insulation tape and heat shrink tubing can shield the wire from damage Cable ties are essential for keeping everything tidy and secure. Test the system on regular basis to identify any issues that could be.
Once autowatch ghost 2 immobiliser has been completed, it is important to conduct a final test of the system prior to switching on the ignition of your vehicle. Ghost immobilisers are able to rearm themselves after 3 to 30 second depending on the model of the vehicle. It also has the option of a Service/Valet mode, which allows you to temporarily disable the system while you are servicing your vehicle or valet parking.
The immobiliser should be hidden in a discreet location beneath the steering wheel or dashboard. It is recommended to use a small amount of paint or duct tape to mark the CAN H and CAN L wires, so that you can easily find the wires during testing. The CAN H and the L wires should also be connected to an electrical source that delivers an uninterrupted 12V. It is important to check the connections after testing because an the incorrect identification of these wires could cause the system malfunction.
Activating the system
A ghost immobiliser blocks your vehicle from starting until you press a sequence of buttons inside the car typically the steering wheel, door panel or central console. The sequence can be altered by the user at any time. Once activated, the system can't be turned off. This is a fantastic option for those who want to safeguard their vehicle from theft.
The system is designed to be undetectable, which means it cannot be detected by modern diagnostics or code-grabbing technologies. It also does not send radio signals which makes it difficult for thieves to find the device.
If the device is found, it will stop the engine from starting. It will also sound an alarm to scare the burglar away. The device can also be used to track the location of the vehicle, which can help police locate it if it is stolen.
If you are interested in a ghost-immobiliser get in touch with the experts at Car Specalist Customs to get a quote and discuss your options. We are fully trained to install a ghost immobiliser on your vehicle, and will make sure it is concealed in a difficult-to-access area. We can also install other security measures, including a kill switch or wheel lock, to protect your vehicle from theft.
Disarming the system
It is important to know how to disarm the Ghost immobiliser if it is fitted to your car. It can be used in the event you forget your keys or your battery is dead. The system is based on a unique PIN code that only you know, so the immobiliser will not be able to start your vehicle unless you enter this code. Pressing the combination buttons on the steering wheel or on the dashboard is the most efficient method of entering your code. This is much easier than using a key fob, and prevents others from copying the remote.
Ghost2 isn't intrusive unlike other immobilisers from the aftermarket which require cutting wires to facilitate installation. It also integrates with the CAN bus system of your vehicle to function. Its main feature is its ability bypass the engine without affecting your vehicle's normal functions, making it difficult for thieves to make use of signal boosters or copy your car keys. Additionally, it doesn't emit radio frequencies, meaning thieves can't detect the system.
The Ghost system also features an option called Transport Mode that allows you to temporarily disable the security system in circumstances like transportation or servicing. This feature is useful for when you're loaning your vehicle out to someone else, without sharing your PIN code or if your vehicle requires to be kept secure when you drive it. Press the service button five times in 2 seconds to activate the Transport Mode. The Ghost system will confirm activation by giving 5 indication signals.
When you're done, remember to save the emergency code in a secure location outside of your vehicle. Then, if you ever encounter a situation where you are locked out of your vehicle, you'll be able to call the technician or company who installed the system, and they'll provide you with the code. If you are unable to reach them then you can try to contact an authorized dealer, but this will involve verification procedures and could incur additional costs.
Apart from the ease of this system, you can also depend on it to safeguard your vehicle from theft and cut down on insurance costs. Many insurance companies offer lower costs or financial incentives for those who install this anti-theft system.